Homebrew-Connection.org

XBOX 360 => Software => xeBuild => Topic started by: idymifoyd on 01 October 2014 à 21:27:37

Title: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: idymifoyd on 01 October 2014 à 21:27:37
Hi Everyone,

i am new to this forum and seeking your help.

i have xbox 360 e 2013 (RGH2) which was working fine on 16747 then i decided to update it to the new firmware 16767 after the nand flash it started giving me an error E79.

i took my nand backup using " simple 360 nand flasher " and built a udpflash using xebuild 2.093 and flashed it using " simple 360 nand flasher ' after the reboot it gave me red light on the power button and on screen it gave me an error E79 (image is attached below) then i re flashed the old nand which i was using before 16747 it still gave me red light but with the scrambled image on top left corner of the screen ( image is attached below)

can any one help me please i would really appreciate it and am 100% sure that it cant be the hardware error since i was using the before the update normally.

Thanks in advance
Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: Dr.Gonzo on 01 October 2014 à 22:27:05
E79 error could be a problem, with your hard disc drive. Please remove your HD and try to boot again. It could be also Bad Blocks, that not remapped, or a faulty Image too.


Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: idymifoyd on 02 October 2014 à 07:18:43
E79 error could be a problem, with your hard disc drive. Please remove your HD and try to boot again. It could be also Bad Blocks, that not remapped, or a faulty Image too.

but am also unable flash the old nand which is was using, its backup i created that dosen't work either  :(
Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: Dr.Gonzo on 02 October 2014 à 22:32:53
Presumably bad blocks will be to blame. You can check your Image with Nand healer or comparable programs.

Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: Swizzy on 03 October 2014 à 02:38:11
but am also unable flash the old nand which is was using, its backup i created that dosen't work either  :(

What did you use to write the "original" image? if you used hardware; what software? did you erase first?

If you only used Simple 360 NAND Flasher (1.3 or older) it's likely that a block was marked bad because of an error somewhere with some data... that'd cause it to not work even with your original...
Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: idymifoyd on 03 October 2014 à 11:20:28
What did you use to write the "original" image? if you used hardware; what software? did you erase first?

If you only used Simple 360 NAND Flasher (1.3 or older) it's likely that a block was marked bad because of an error somewhere with some data... that'd cause it to not work even with your original...

I used Simple 360 nand falsher and its v1.2  :'( . and yes the backup nand is also not working. I had checked my nand for the bad blocks in j-runner it dose not show any, but when i flash my nand via XELL it says

block 0x25a seems bad, stats 0x00000204
Block cannot be recovered (A.K.A it's really bad )

and the starts processing the rest.

the image is attached below.

looking forward to your reply.

Thanks.
Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: Swizzy on 04 October 2014 à 10:52:58
I used Simple 360 nand falsher and its v1.2  :'( . and yes the backup nand is also not working. I had checked my nand for the bad blocks in j-runner it dose not show any, but when i flash my nand via XELL it says

block 0x25a seems bad, stats 0x00000204
Block cannot be recovered (A.K.A it's really bad )

and the starts processing the rest.

the image is attached below.

looking forward to your reply.

Thanks.

Can you send me your dump and key so i can check it?

Sent from my GT-I9300 using Tapatalk
Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: idymifoyd on 04 October 2014 à 11:37:00
Can you send me your dump and key so i can check it?

Sent from my GT-I9300 using Tapatalk

from dump you mean the backup i took before updating and the cpu key ?
Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: Swizzy on 04 October 2014 à 11:41:33
from dump you mean the backup i took before updating and the cpu key ?
Yeah, but... probably best if you give me one that's fresh (make a new one and give that to me aswell)

Sent from my GT-I9300 using Tapatalk

Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: idymifoyd on 05 October 2014 à 16:40:08
Yeah, but... probably best if you give me one that's fresh (make a new one and give that to me aswell)

Sent from my GT-I9300 using Tapatalk

dude thanks for you're help but i got it fixed from the local modder this time cause it was taking too long :)
Title: Re: Xbox 360 e 2013 RGH2 red power light E79 on screen after update to 16767
Post by: Swizzy on 07 October 2014 à 15:20:18
dude thanks for you're help but i got it fixed from the local modder this time cause it was taking too long :)

Np, altough... not sure why you're blaming me for taking time? xD